How To Set Up Led Strip Lights Around Your Room

Led strip lights are a great way to add together color, way, and personality to your sleeping room.

When done correct, the results are excellent and fulfilling.

Unfortunately, not many people are skilled enough to install LED low-cal strips themselves, not because it's that hard to ready upward, simply because they've never done it earlier.

If you fall into this category of people, worry no more. This commodity is here to simplify the process and assistance you ready your Led light strips yourself.

How To Fix LED Lights In Bedroom

With a little bit of planning, we can brand sure that we're making the right decisions for your bedchamber, like cutting the right lengths to have plenty led strips to create that personalized design of yours.

Here are the things you'll need to gear up upward LED lights in your bedroom:

LED Strip Lights

There are many available brands of LED strips out at that place, but the main thing to annotation when ownership LED strips is the voltages. They're both 12v LED strips and 24v LED strips.

Because you're new to setting upward LED strip lights, it's recommended that you get a 12v LED strip. 12v LED strips are shorter distances betwixt cut-line intervals (one inch for 12V vs. two inches for 24V).

Simply If you wish to get strips for maximum efficiency, the 24V DC is recommended because the chances for voltage drop here are minimal compared to 12v strips.

We recommend these LED lights if this is your first fourth dimension hanging LED lights.

Power Supplies

Considering LED strips run on low voltage DC, they will need a power supply device or adapter that converts 120V/240V Air conditioning, the advisable voltage point that LED strips tin utilise.

LED Controllers

The LED controller is substantially a remote command for your lights; with this, you can power light strips on or off, change the color, suit the effulgence level, and switch colour-changing modes.

LED Connectors

LED connectors will help y'all connect two strips cease-to-end to arrive longer.

Below are recommended tools that you'll need to ensure that your LED lite stays in place and prevent them from falling. These tools will aid to hang the LED lights much more accessible.

Measuring tape
Wire strippers
Black electrical tape
Sharp scissors
Screwdrivers

These are the tools that we recommend to start hanging your LED lights. Next, nosotros're going to walk yous through, step past pace, how to hang them.

Pace Past Step Guide

Nosotros're going to walk yous step by pace on installing your LED lights in your room.

Let's get started.

Test Your Supplies

Information technology's ever best to test your LED strips and controllers to ensure they are working correctly. This way, returning them would be easy if they don't work.

If the lights are functional, you're looking for the color, color temperature, etc. For the controller, if it's an RGB (Red Green Blue) organization, ensure all the lights come on and become your desired effects.

Prepare LED Mounting Surfaces

Earlier you brainstorm, brand sure your surfaces are prepared to make mounting your strips fast and easy.

To ensure the strips attach well to your surface, ensure that the surface is clean, polish, dry out, and stable, with examples beingness a wall, the floor, or even your ceiling.

Practise not apply on crude or textured surfaces. Remove all dirt, oil, and other contaminants with a surface cleaning solvent like isopropyl alcohol (70% alcohol and 30% water).

Mensurate Your Surface Lengths

Information technology is appropriate that when planning the layout of strip light installation, a total length measurement of light strips is required.

Too, make sure to measure the length for each leg of the installation. Always continue your measurements shut by to use them when cut the LED strips.

Cutting LED Lights

With a simple pair of scissors, you can hands cutting strips by locating marked cuttable segments visible on LED strips. Nigh common LED strip lights tin can be cut every three or half dozen LEDs.

Always make sure to cutting precisely along the cutting line. Also, ensure you're leaving enough copper pads on each end of the LED strips as they will be your soldering base for soldering connexion or as connection points for solderless LED connectors.

To connect LED light strips, you need to use a connector clip. Push the open cease of the copper terminate of the strip into the connector clip and shut to lock information technology in.

How To Stick LED Strips To Surfaces

Firstly, unroll the desired length of LED strips you want to work with
To deeply adhere an LED strip to your surface, Remove the agglutinative backing and simply stick to the surface
Press downwards on the LED strip to firmly adhere the strip to the surface, this mode, you're minimizing the chances of getting air bubbles underneath the strip

Connect The LED Strip To The Master Power Supply

One time your LED strip lights are placed, you lot can attach them to the ability adapter and controller. Plug information technology into your electric outlet and utilize the remote control. Please turn information technology on, and printing any color on the remote control to change the lighting color.

Always brand sure to unplug the bombardment insulation sheet before utilize.

Next Steps

Once you lot plug in the ability supply, y'all should be fix to get! The LED lights add a new vibe to the room you're placing them in. If you're adding them to a recording studio, it's a great way to add together ambiance to a dimly lit room.

Other spots where yous tin place the LED lights are behind TVs and windows. LED lights will instantly concenter the center of the guest when they enter the room.

Nosotros've compiled a complete list of frequently asked bedroom questions for new and experienced homeowners.

Our experts respond these questions to assist help you lot through DIY projects and dwelling house repairs.

If you accept whatever questions about changing LED lights, permit us know in the comment section below.